• Custom Brake Hose (0.1m - 5m)

Custom Brake Hose (0.1m - 5m)

  • £22.50


Available Options


Average Review Rating

10 reviews

Custom made bespoke hoses for the same sort of price as an “off the shelf” item. The quality of these hoses simply cannot be beaten, stainless steel braid with a clear or coloured wipe clean PVC coating, & stainless-steel end fittings all guaranteed for life.

NOTE - None of our unions are supplied with nuts or bolts, all nuts and banjo bolts are sold separately, banjo fittings are provided with 2 copper washers per fitting

As these are custom, please understand that the orders will take time, the length of time between order and dispatch will vary dependent on the specification of the hose requested and the number of orders we currently have. I do my best to get all custom hose orders out within a week but again this can vary slightly, if you need an order in a hurry please message first as it may not be possible for me to get to your order if I have multiple other orders in at the same time and I can advise on a rough time frame

All measurements are inclusive of unions so please provide measurement from the center eye of a banjo and the furthest end of any other union, exclusive of any bends, i.e. the hoses are measured simply lying next to a tape measure so if you need a 90-degree bend on a union you do not need to measure around the bend of the hose, just to wherever the end of the union will end up.

The Price will automatically adjust as you enter your hose details if extra charges apply

Male or female swivel, with bend if required up to 90 degrees (additional cost for bend, price change made automatically on selection)

10mm Banjo, (copper washers supplied FOC) straight or bent 5 - 90 degrees in 5-degree increments, banjos can also be swept to left or right

Banjo Bolts are not included with Banjo fittings, these can be found in the Brake Hose & Brake Parts section of the website

Male Bulkhead connector - without nut (supplied separately)

All the above available in 3/8 x 24 UNF, M10 x 1.0, or M10 x 1.25 threads

Nonstandard ends include, 8mm & 12mm banjos, female fixed end, female bulkhead connector, male & female swivels with bends & specialized fittings if you have particular requirements you can’t fulfill within our standard ordering procedure above the please email your requirements to info@furoreproducts.co.uk

Please be aware that due to monitor/computer differences and changes made by our supplier, the colour of hoses may differ slightly. We make hoses to a tolerance of + or - 5mm, it is ALWAYS better to have a hose slightly too long than too short, a short hose can be dangerous, so please make adequate allowance when specifying your hoses. If you require a hose where absolute accuracy is required, then please contact us at the time of order & we will do our best to ensure accuracy.

Hose Specification

Line Inner Material : PTFE

Line Outer Material : Stainless steel (303/304) and protective PVC cover

Fittings Material : Stainless steel (303/304)

Temperature Range : -70 to 260 degrees Celsius (-94 to 500 degrees Fahrenheit)

Inside Diameter : 3.5mm (0.138")

Outside Diameter : 7.5mm (0.295")

Maximum Working Pressure : 290 Bar (4206 PSI)

Burst Pressure : 870 Bar (12618 PSI)

Minimum Bend Radius : 38mm (1.496")

  • 5 Awesome
    100%
  • 4 Great
    0%
  • 3 Average
    0%
  • 2 Bad
    0%
  • 1 Poor
    0%

100% Customers recommend this product

Reviews For Custom Brake Hose (0.1m - 5m)

  • (5)

Total Reviews (10)
click here to add a review for this product.


Tags: custom, brake, hoses, hose, bespoke, stainless, steel, braid, PVC, coating, unions, banjo, male, female, swivel, copper, washers, 3/8, 24, M10, 1.0, 1.25, threads, thread